|
HOME
E-Mail
How to?
Application Guide
Sealants
Perma-Chink
Energy
Seal
Woodsman
Check
Mate
Chink-Paint
Stains & Finishes
Lifeline Ultra-7
Lifeline Ultra-2
Lifeline
Exterior
Lifeline
Advance
Lifeline
Interior
Acrylic
Gloss/Satin
Prelude/After Blast
Endure Deck Stain
Sure
Shine
UV BOOST
Log End Seal
Preservatives
Shell-Guard
Shell-Guard RTU
Armor-Guard
Restoration
Products
M-Balm
E-Wood
Epoxy
Kit
Wood Cleaners/Strippers
Wood ReNew
Log Wash
Smart Strip
S-100
Oxcon
Dry-in Products
Trap Rod
&
Backer
Rod
Gasket
Tape
Log Fasteners
Our
Tools
|
|
PCSI S-100
Environmentally Friendly Finish
Remover
S-100 Finish Remover is an environmentally
friendly, water-based solvent that may be used to remove many oil
and water based finishes. Perma-Chink Systems developed a finish
remover using new technology originally developed for removing paint from
aluminum aircraft surfaces.
Supplied as a ready-to-use gel, it is easily applied with a short
bristled brush, paint roller, or airless sprayer. Within a few minutes
it begins to soften the finish and since it is a gel, it stays wet and
active for a fairly long period of time. Once the finish has sufficiently
softened, it can be removed by simply pressure washing.
S-100 will not darken or discolor the wood, will not corrode or
discolor metal surfaces, nor will it harm log home chinking or sealants.
Although it is effective for removing most log home finishes, there are
some high performance coatings that may require a more aggressive chemical
stripper. Perma-Chink Systems recommends that a sample of S-100 be obtained
from them and tested on the finish you want to remove prior to placing an
order.
S-100
FEATURES AND STATISTICS
- Removes
most finishes from logs, siding and deck surfaces.
- Is environmentally friendly.
- Will not corrode or discolor aluminum or
other metals
- S-100 is not recommended for removing
lead-based paint or paint that was applied before
1972.
|
|
|
Shelf Life
|
|
|
Application Temperature
|
|
|
Application Methods
|
- Safety equipment, bucket, brush or
roller, paint scraper, rags, and a pressure washer
capable of generating at least 500 to 600 psi.
|
|
Surface Preparation
|
|
|
Frequency
|
|
Special Instructions
|
- One to two applications, depending
on severity
- Apply from bottom-up, rinse from
top-down
- Rinse thoroughly
|
|
S-100
|
5 gallon $180.00
Price Effective
January 30, 2012
|
|
|
PCSI S-100 Instructions
PCSI S-100 Finish Remover is an environmentally friendly,
water-based solvent that may be used to remove many oil and water based
finishes. However, it may not be effective for removing some high performance
coatings that may require a more aggressive chemical stripper. Unlike
sodium or potassium hydroxide strippers, PCSI S-100 will not darken nor
discolor the wood.
Application Tips
- Always try a sample of PCSI S-100
to see if it works on your finish
- Make sure the surface is clean and
dry before applying.
- Use only Lifeline brand water-based
stains over After-Blast.
Directions for Use
S-100 works best when applied at temperatures between
50°F and 90°F and try to avoid working in direct sunlight. Work
on small sections (50 square feet or so) at a time. Apply a generous amount
of S-100 to the wood surface using a brush or roller. If removing a finish
from a wall, start at the bottom of the wall and work your way up. Allow
the S-100 to remain on the surface for at least 10 minutes. If it starts
to dry out, a light misting with water will help keep it active.
Once the finish has softened, remove it with a pressure washer.
On walls, pressure wash starting at the top of the area and work your
way down. If there are spots where pressure washing has not removed
all of the finish, try scraping off the remaining finish with a paint
scraper while the finish is still soft. Protected areas under porch
roofs, soffits, etc. may need a second application to remove all of
the finish.
Once the finish removal process is completed, be sure to thoroughly
rinse the surface in order to remove any PCSI S-100 residue and return
the wood to its proper pH balance.
EQUIPMENT: Safety equipment, bucket, brush
or roller, paint scraper, rags, and a pressure washer capable of generating
at least 500 to 600 psi. For the most efficient removal of the finish,
use a pressure washer with an output of three gallons per minute or
greater and a 15 degree fan tip nozzle.
COVERAGE RATE: Coverage will be approximately
50 to 100 square feet per gallon depending on the surface texture.
CLEAN UP
Use soap and water to clean tools and equipment.
STORAGE
Do not allow S-100 to freeze.
SAFETY INSTRUCTIONS
Keep out of reach of children. Although PCSI S-100 is not nearly
as corrosive as many commonly used finish removers, be sure to wear
a long sleeved shirt, rubber gloves and eye protection during use. If
exposed, flush eyes with water and wash skin with soap and water. Rinse
down plants, shrubs, and grass with plenty of water if S-100 comes in
contact with them.
|
Forms of Payment:
We accept MASTERCARD,
VISA, DISCOVER CARD and AMERICAN EXPRESS.
Shipping:
We ship to your jobsite. All orders are shipped
within 24 hours.
Substantial freight discounts may occur on shipments
weighing 200 pounds or more.
Orders accepted before noon are same day shipment.
Terms:
Prices effective
January 30, 2012. Prices are subject to change without notice.
All prices are in US dollars. Seller not responsible
for consequential damages.
All returns require advance approval number and will
be subject to 15% restocking charge.
|